• Products
    • D21 Adj UCA
    • 320/520/521/620 Disc Brake Kit >
      • Donor Vehicle and Part Information >
        • Hub Info
        • Rotors
        • Calipers
        • Hoses - Banjo Bolts
        • Master Cylinder
    • 320/520/521/620(drum) Urethane UCA Bushings
    • 311 Roadster Disc Brake Kit >
      • Caliper options
      • Breck Myers Manifold Blueprint
    • 1200 Disc Upgrade Kit
    • 411 Disc Brake Kit
    • Pushrod
    • Spacer for 320/520/521
    • L-Series Downpipe Flange
    • Wheel Spacers
  • Manuals
  • How To's
    • King pin rebuild info
    • Installations >
      • Truck Kit Install >
        • Stock Rims
      • Roadster Kit Install
    • 5 Lug Swap, Nissan D21 Hardbody
    • Automotive >
      • Door Hinge Repair
      • L-Series Valve Adjustment
      • Headlight Switch Restoration
      • Differential / Rearend >
        • Spider Gear Swap
      • Wiper Repair - Servicing >
        • Wiper Blade - Replacing
      • Tension Rod Modification
      • Tie-rod removal
      • Brake Pad and Rotor Replacement
      • Ignition Switch
      • Weber DGV Rebuild
      • Ignition Wires
      • Electronic Ignition for E & J series engines
      • Steering Column Mods
    • General/Misc >
      • HF Electric Hoist Mount >
        • Misc Electric Hoist Info
      • Airbody saw blade option
      • Bending Brake for Shop Press
  • Misc
    • L16 Exhaust Flange
    • K772 Ball Joint Wrench
    • Garage Door White Board
    • Spindle comparison 311-411
    • Big Brake, Ball Joint, 5 Lug
    • 410/411 brake upgrade pics
    • Eric Capps' 620 brake kit installed
    • Adjustable UCA
    • Ball Joint Info/Parts
    • Truck Firewall Steering Column Flange/Gasket
    • L-series Timing Chain Tension Retainer
    • Brake Kit CAD
    • Spindle Template for aluminum bracket
    • Weber Adapters
    • 9 x 20 CNC Lathe
    • Brake Master Cylinder Anatomy
    • 521 Wiring Schematics
    • RX-7 Auto-Manual Conversion Brackets
    • Misc Pics
    • Enco 1340 Reference
    • Vise Hold Down Blocks
    • Dual Point Distibutor Info
    • Misc Pic Dump
  • Car Show Pics
    • Blue Lake 2012
    • Goodguys Spokane 2012
    • Rod Run Long Beach 2012
  • FAQ Page
  • Contact BHF
  • BlueHandsVideo
  • HB Adj UCA
  • Jered's 312 Wagon pics
  BlueHandsFab.com

Wheel Spacers

These wheel spacers have been made, primarily for people buying/using the stock Datsun truck rims with our disc kit.  The register nice and close to the 12mm lug bolts.  Because of the "dish" on the rear drums of the Datsun trucks, some rim styles may require a spacer to mount correctly.  Take your own measurements to make sure 1/8" is enough. 

The bolt pattern is 6 on 5.5", which is the most common 6 lug pattern.  These will probably work on almost any make/model of truck with a 6 lug hub.

The finish of the steel may vary from batch to batch, but the fit will remain constant.  Since these are steel, they will rust.  They may weld themselves to the brake drum if you do not take the necessary precautions to inhibit the rust.




The pictures above and this video show the difference between the typical cast aluminum spacer found at most parts stores and our laser cut steel spacer.